Wow. Well team, the reason it’s been a little quiet around this blog is because I haven’t been able to move of late without bumping into a deadline. This is made all the more incredible by the fact that the only thought I had towards making a resolution this year was to cut down on the amount of shows that I apply for. If I’m honest, though, two of the three major deadlines this month were destined to collide from the outset (and yes, I signed up to both last year), and only really met so sharply owing to a bit of misfortune. Read on!
I had spent a couple of weeks working diligently in my studio on a new piece, getting it ready for a photography deadline. Having squared it away finally – after going to Nancy’s Sewing Basket and buying only about 1/3 of the cotton and linen ribbons in the store – I was taking photographs of it and some other pieces that I had finished a while back for the same application, which were due via email the following day.
In order to take photos of these bigger works I had, for the second time, transplanted my photography setup to a corner of the basement, taking advantage of the fact that we had brought inside our outdoor table for the winter. Down there I can sprawl out across the walls and of course the table, and position the lights more easily. Incidentally the setup remains downstairs; I’ve now built an overhead light-bouncer that doubles as a slightly more efficient way of hanging works than sticking pins into the sandalwood-paneled ceiling in the wardrobe that I was using as my photography booth before. (The wardrobe also acts as my storage/packing room, so it’s still getting plenty of action.)
I had promised myself that after photographing the recently completed and particularly tricky to arrange piece, I would be able pack it in for the night. It was about 8pm on Friday and Turbo was kindly preparing dinner for probably the 5th time that week. I was jubilant! I was literally clapping and jumping around the basement as I tidied and turned off lights. I had finally finished the work and captured it, marking the end of what had been a grueling couple of weeks of making, and the agonising decision making that sometimes attaches itself to a work when one is inventing a new thing and then figuring out how that thing is going to operate as a jewel in the world.
I had been checking in my images on the computer as I went, so I knew that I had some suitable sample images to go through that night, to figure out if there was anything that needed to be re-shot in the morning. The tricky piece I decided to leave on the table but I wanted to cover it (our basement ceiling is not the finest example of the art; dust and cobwebs occasionally drift down), so I grabbed the big shoebox that was slightly over-full of work and stopped past the table with the one piece left out in the open to cover it with tissue. Having done that I picked up the box, making a sharp right turn to head towards the staircase, and simultaneously sent the work on top of the overstuffed box to the ground, upon which it landed with a sharp “Crack!”
The work in question was wrapped in tissue and then put into a plastic self-locking bag, on top of a bunch of other similarly wrapped works. Plastic on plastic is slippery and when a person makes a sharp turn with a bunch of horizontally stacked bags, they’d wanna have a good hold on all of them…
At first I thought that the smacking sound was probably right for the wood-meeting-concrete scenario that had played out so effortlessly, that I didn’t think to worry. I put the box down on the floor, carefully, and then turned back to the dropped work. The noise was replaying in my head as I reached for it, and despite the packaging surrounding it so I couldn’t see in, I knew that what I had made was gone. My hand told me the truth, which echoed my thought. The tension had dropped, the work felt mushy. Before this, the wood had been hard and the tension of threads weaving inside and around the piece felt rigid.
This was not good. It’s one of those moments that had happened so innocuously that I almost felt that I should simply be able to access some sort of ‘undo’ button, where I could rewind the time and get my work back, whole. I think I was in that state of shock for a couple of minutes, long enough to make some regretful ‘arrgh’ noises and to wonder why I wasn’t yet crying. Then Turbo came down the stairs to see me huddled on the floor as I slowly re-wrapped the work and put it back into its plastic shroud. He dutifully claimed that I could fix it, of course I could, and that’s when the tears came. I had seen it. The tension that made the piece from ‘object’ into ‘wearable’ had also accelerated its demise. It was made from a turned wood bowl, which had itself been made from laminated timber, which I had gutted by sawing a pattern into its body and drilling holes and stringing waxed linen around and through it, rejoining some of the released sections to the bowl’s interior.
The wood, vintage if not antique, had been in use for a long time and joined for a longer one. Despite its considerable thickness – I gauged it at around 1cm thick all over, thinner with some shallow carving and thicker in the corners – it cracked at the lamination faces and at any point that I had created extra stress, and there were lots of those. Plenty of 90° angles next to thinner sections of material that I had left behind and holes in line with even sharper points, laying along the same line of grain. There were largish pieces, yes, but bits and pieces of splinter-size too.
Now, thanks to my style of resourcefully making several jewels out of a single found object, I had not one broken work, but three. The other jewels made from the same bowl, two neckpieces, were now context-less. And that’s not to mention another two works that are locked into a narrative with this piece. I was doomed.
The only thing that I could think to do that night was submit the work as it had been photographed and then apologise if it was chosen, presenting in its stead a replacement that had followed much the same plan. (That was if I didn’t quit the industry all together, or just give up on making this application that I had toiled so hard toward, as I didn’t think I could, in good conscience, throw my unfettered support behind a lost work.) The revision/remake is eventually what happened; I found a replacement object within my collection (incidentally, bought at the same time, from the same now-closed antique importers down in South Lake Union, and more importantly made of m e t a l ), altering the plan to fit its slightly different dimensions.
To be honest, I think it’s the better version. Some parts were improved upon in the design and others in the making, but of course the metal made a big difference to the aesthetic. After the experiments that went to making its older sibling, the manufacturing was more linear and went quicker. The final result, for better or worse, is less chunky, more refined.
The morning after my mishap, I was slowly coming to terms with the idea that I would have to finish fine-tuning an application to include what I knew was a destroyed work, whilst lying in bed checking my twitter feed. And of all the things… Out of nowhere came my reprieve! On twitter I read, right from the source, that the deadline for that night had been extended. By a week. I had a whole seven days to get the new work together. What was there left to decide? That day I took a well-earned rest day, and got back work the following morning.
And re-making that piece instead of moving on to new works as planned is how I sent my next two deadlines crashing into one another. Thankfully I’ve now dug myself out, and my reward is to catch up on paperwork…